Effect of Screw Distribution on the Structural Response and Buckling Behavior of Built-Up Cold-Formed Steel Columns

Authors

  • Zamzami Septiropa Department of Civil Engineering, University of Muhammadiyah Malang, Malang, Indonesia
  • Abi Mufid Octavio Department of Mechanical Engineering, University of Muhammadiyah Malang, Malang, Indonesia
  • Achmad Fauzan Hery Soegiharto Department of Mechanical Engineering, University of Muhammadiyah Malang, Malang, Indonesia
  • Arizu Sulaiman School of Civil Engineering, University of Technology Malaysia, Johor Bahru, Malaysia

DOI:

https://doi.org/10.46604/peti.2026.16660

Keywords:

built-up cold-formed steel, screw distribution, finite element analysis, buckling behavior

Abstract

Built-up cold-formed steel (CFS) columns offer a high strength-to-weight ratio, but the influence of screw distribution on elastic response and buckling behavior remains insufficiently understood. This study investigates five screw distributions (S50–S90) in double back-to-back (dBB) and double flange-to-flange (dFF) columns using finite element analysis and experimental compression tests. Six self-drilling screws and a column length of 500 mm are maintained, so screw spacing and end distance vary simultaneously. In dBB, equivalent elastic strain and stress vary by 22.31% and 22.94%, respectively, compared with 2.64% and 6.82% in dFF. The buckling load factor (BLF) varies by 7.11% for dBB and 3.22% for dFF, indicating greater sensitivity to screw distribution. S60 produces the highest BLF for dBB (2.4774), whereas S80 produces the highest for dFF (3.3173). These findings demonstrate that profile orientation influences structural response and relative elastic buckling stability. The BLF indicates comparative elastic stability, not actual ultimate compression capacity.

References

X. Zou, Y. Zhu, and L. Zhang, “A Decade of Developments in the Mechanical Performance of Cold-Formed Steel Members,” Mechanics of Solids, vol. 61, no. 2, article no. 89, 2026.

H. Hendaryati, A. F. H. Soegiharto, R. D. Virdianto, and A. Saifullah, “Analysis of the Effect of Cooling Media Variations on Tensile Strength of Electrical Welding Results of S45C Steel,” AIP Conference Proceedings, vol. 2453, no. 1, article no. 020004, 2022.

M. A. Dar, S. A. Baba, M. Zakir, and A. R. Dar, “Flexural Performance of Sustainably Composite-Stiffened Cold-Formed Steel Built-Up Beams with Rectangular Compression Flanges,” The Structural Design of Tall and Special Buildings, vol. 35, no. 2, article no. e70130, 2026.

D. B. Hussein and A. B. Hussein, “Investigating the Factors Influencing the Strength of Cold-Formed Steel (CFS) Sections,” Buildings, vol. 14, no. 4, article no. 1127, 2024.

N. Kharghani and C. Mittelstedt, “Global–Local–Distortional Buckling of Shear-Deformable Composite Beams with Open Cross-Sections Using a Novel GBT–Ritz Approach,” Journal of Composites Science, vol. 9, no. 11, article no. 608, 2025.

N. Subeki, A. F. H. Soegiharto, A. Firkriyanto, and N. Gidiazalia, “Crack Propagation Analysis of Fatigue Due to External Corrosion on the Construction of the Ferris Wheel in Alun-Alun Kota Batu,” Journal of Advanced Research in Applied Mechanics, vol. 111, no. 1, pp. 62–73, 2023.

M. Elsawi Mahmoud, A. El-Sisi, A. Elbelbisi, H. Elemam, and H. Salim, “Performance of CFS Trusses Self-Drilling Screws Connections Under Extreme Loads,” Structures, vol. 74, article no. 108592, 2025.

J. Yang, K. Luo, W. Wang, Y. Shi, and H. Li, “Research on the Flexural Buckling Behavior of the Cold-Formed Steel Back-to-Back Built-Up Columns with Σ-Section,” Engineering Structures, vol. 302, article no. 117404, 2024.

S. T. Vy and M. Mahendran, “Screwed Connections in Built-Up Cold-Formed Steel Members at Ambient and Elevated Temperatures,” Journal of Constructional Steel Research, vol. 192, article no. 107218, 2022.

N. Soysal and Z. Fırat Alemdar, “Numerical and Experimental Assessment of Structural Performance and Axial Compression Capacity of Screw-Connected Built-Up Cold-Formed Steel Members,” Buildings, vol. 16, no. 9, article no. 1651, 2026.

H. Wu, L. Sui, X. Liu, S. Liang, and T. Zhou, “Shear-Slip Constitutive Model of Screw-Fastened Connections and Application in Numerical Analysis of Built-Up Back-to-Back Cold-Formed Steel Columns,” Thin-Walled Structures, vol. 186, article no. 110710, 2023.

Z. Septiropa, M. H. Osman, A. B. A. Rahman, and M. A. M. Ariffin, “Effect of Screw Distance on Combined Profiles Cold-Formed Steel in Increasing the Compression Member Capacity,” IOP Conference Series: Materials Science and Engineering, vol. 527, no. 1, article no. 012080, 2019.

P. Deniziak, E. Urbańska-Galewska, and M. Gordziej-Zagórowska, “Normal Stress Distribution in Built-Up Cold-Formed Column in Relation to Interconnecting Bolt Spacing,” Scientific Reports, vol. 14, no. 1, article no. 5415, 2024.

M. B. Suhaib and M. A. Tantray, “Flexural Integrity Between the Individual Channels of Built-Up Cold-Formed Steel Beams,” International Journal of Steel Structures, vol. 23, no. 2, pp. 503–520, 2023.

J. Feron, P. Latteur, and J. Pacheco de Almeida, “Static Modal Analysis: A Review of Static Structural Analysis Methods Through a New Modal Paradigm,” Archives of Computational Methods in Engineering, vol. 31, no. 6, pp. 3409–3440, 2024.

M. N. Bin Kamarudin, J. S. Mohamed Ali, A. Aabid, and Y. E. Ibrahim, “Buckling Analysis of a Thin-Walled Structure Using Finite Element Method and Design of Experiments,” Aerospace, vol. 9, no. 10, article no. 541, 2022.

A. B. Hussein, “Structural Behaviour of Built-Up I-Shaped CFS Columns,” Scientific Reports, vol. 14, no. 1, article no. 25628, 2024.

K. Mitsui, A. Sato, and K. Ikarashi, “Required Number of Self-Drilling Screws for Built-Up Column Comprising Cold-Formed Lipped Channel Sections to Ensure Flexural Buckling as a Single Unit Member,” Japan Architectural Review, vol. 6, no. 1, article no. e12354, 2023.

M. Abbasi, K. J. R. Rasmussen, M. Khezri, and B. W. Schafer, “Computational Modelling of Built-Up Cold-Formed Steel Columns and Parametric Studies,” Thin-Walled Structures, vol. 191, article no. 111035, 2023.

F. De’nan, K. K. Choong, J. Y. Ling, and N. S. Hashim, “Finite Element Analysis of Buckling Behavior for Cold-Formed Steel Hat Purlins with Openings,” International Journal of Steel Structures, vol. 22, no. 4, pp. 982–1001, 2022.

J. He and B. Young, “Web Crippling Design of Cold-Formed Steel Built-Up I-Sections,” Engineering Structures, vol. 252, article no. 113731, 2022.

M. Amjad, S. Badshah, S. Ahmad, M. Badshah, S. Jan, M. Yasir, et al., “Finite Element Modeling of Stress Distribution and Safety Factors in a Ti-27Nb Alloy Hip Implant Under Real-World Physiological Loading Scenarios,” PLoS ONE, vol. 19, no. 8, article no. e0300270, 2024.

Downloads

Published

2026-10-31

Issue

Section

Articles

How to Cite

[1]
“Effect of Screw Distribution on the Structural Response and Buckling Behavior of Built-Up Cold-Formed Steel Columns”, Proc. eng. technol. innov., vol. 34, pp. 138–153, Oct. 2026, doi: 10.46604/peti.2026.16660.