Effect of Corrugation Angle on Heat Transfer Studies of Viscous Fluids in Corrugated Plate Heat Exchangers

Authors

  • B Sreedhara Rao
  • Surywanshi Gajanan D
  • Varun S
  • MVS Murali Krishna
  • R C Sastry

Keywords:

corrugation angle, corrugated plate heat exchanger, Nusselt number, viscous fluids.

Abstract

In the present investigation heat transfer studies are conducted in corrugated plate heat exchangers (PHEs) having three different corrugation angles of 300, 400 and 500. The plate heat exchangers have a length of 30 cm and a width of 10 cm with a spacing of 5 mm. Water and 20% glycerol solution are taken as test fluids and hot fluid is considered as heating medium. The wall temperatures are measured along the length of exchanger at seven different locations by means of thermocouples. The inlet and outlet temperatures of test fluid and hot fluid are measured by means of four more thermocouples. The experiments are conducted at a flowrate ranging from 0.5 lpm to 6 lpm with the test fluid. Film heat transfer coefficient and Nusselt number are determined from the experimental data. These values are compared with different corrugation angles. The effects of corrugation angles on heat transfer rates are discussed.

References

R. K. Shah, W. W. Focke, Plate heat exchangers and their design, Hemisphere Publishing Corporation, pp. 337-349, 1988.

F. P. Incorpera, P. D. Dewitt, Fundamentals of heat transfer, John Wiley and Sons, V ed., 2004.

J. L. Goldstein, E. M. Sparrow, “Characteristics for flow in channel,” Int. Heat Transfer, pp. 205-209, 1977.

T. Nishimura, S. Murakami, S. Arakawa, Y. Kawamura, “Flow observations mass transfer characteristics in symmetrical wavy walled channel at moderate Reynolds numbers for steady flow,” Int. J. Heat and Mass Transfer, vol. 33, pp. 835-845, 1990.

F. S. K. Wanakulasuriya, W. M. Worek, “Heat transfer and pressure drop properties of high viscous solutions in plate heat exchangers,” Int. J. of Heat and Mass Transfer, vol. 1, no. 51, pp. 52-67, 2008.

Marcus Reppich, “Use of high performance plate heat exchangers in chemical and process industries,” Thermal Science, vol. 38, pp. 999-1008, 1999.

M. Gradeck, B. Hoareau, M. Lebouche, “Local analysis of heat transfer inside corrugated channel,” International Journal of Heat and Mass Transfer, vol. 48, pp. 1909-1915, 2005.

J. E. O. Brien, E.M. Sparrow, “Corrugated- Duct heat transfer, pressure drop, and flow visualization,” Journal of heat transfer, vol. 104, pp. 410-416, Aug. 1982.

J. E. Goldstein, E. M. Sparrow, “Heat/mass transfer characteristics for flow in a corrugated wall channels,” ASME Journal of Heat Transfer, vol. 99, pp. 187-195, 1977.

P. J.Heggs, P. Sandham, R. A. Hallam, C. Walton, “Local transfer coefficient in corrugated plate heat exchanger channels,” 5th UK National Heat Transfer Conference, vol. 75, no. 7, 1997.

S. D. Pandey, V. K. Nema, “Investigation of the performance parameters of an experimental plate heat exchanger in single phase flow,” Energy Engineering, vol. 1, no. 1, pp. 19-24, 2011.

J. H. Lin, C. Y. Huang, C. C. Su, “Dimensional analysis for the heat transfer characteristics in the corrugated channels of plate heat exchangers,” Heat And Mass Transfer, vol. 34, pp. 304–312, 2007.

V. Ozbolat, N. Tokgoz, B. Sachin, “Flow characteristics and heat transfer enhancement in 2D corrugated channels,” International Journal of Mechanical Engineering, Industrial Science and Engineering, vol. 7, pp. 999-1003, 2013.

Downloads

Published

2015-04-01

How to Cite

[1]
B. S. Rao, S. Gajanan D, V. S, M. M. Krishna, and R. C. Sastry, “Effect of Corrugation Angle on Heat Transfer Studies of Viscous Fluids in Corrugated Plate Heat Exchangers”, Int. j. eng. technol. innov., vol. 5, no. 2, pp. 99–107, Apr. 2015.

Issue

Section

Articles